TinyRC.com - XMODS, XMOD, Micro Flight, ZipZaps, ZipZaps SE, Bit Char-G, MicroSizers, TTTT, Plantraco Desktop Rover, SuperSlicks, Digi Q, Forums, News, Pictures, Parts, and Shop
Forums, XMODS, XMOD, Micro Flight, ZipZaps, ZipZaps SE, Bit Char-G, MicroSizers, TTTT, Plantraco Desktop Rover, SuperSlicks, Digi Q
XMODS Hop-Ups, XMODS Parts, XMOD Hop-Ups, XMOD Parts, Bit Char-G Hop-Ups, Bit Char-G Parts, MicroSizers Hop-Ups, MicroSizers Parts

Go Back   TinyRC.com > 1/24 and Smaller > XMODS > XMODS Mods and Projects

Reply
 
Thread Tools Display Modes
  #1  
Old 01-03-2004, 06:23 PM
ax0n
Guest
 
Posts: n/a
Differential Fun - Quick Change between RWD/AWD in the paddocks!

Well, I bought the AWD kit specifically for the rear ball differential. Kind of disgruntled with the fact that LSD did almost nothing for my steering/traction issue, I played with the differentials a bit. I remember people here saying you can loosen the screws and tighten them to change the ball diff's characteristics.

I found that you can loosen each of the 3 screws about a whole turn (maybe a little more, but definitely not 2 whole turns) and end up with freewheel spinning on the back end, ghetto FWD. That was okay, but not my style.

here's what I did.

I put the red gear diff on the back, and the red ball diff in front, exactly opposite what radio shack says to do. With the body shell off, you can get access to the differential screws one at a time, by rotating the wheels till you see a screw right near the front of the suspension. Get on it with a small screwdriver.

Make the differential really tight for a full AWD effect.

Loosen it up a lot for a more rear-biased drive with enough front wheel pull to keep the oversteer and spinouts in check

or

Loosen it further for almost pure RWD only. The fronts will still spin if you are off the ground, but with any pressure, the fronts stop and have no resistance.
Reply With Quote
  #2  
Old 01-03-2004, 07:35 PM
Joey's Avatar
Joey Joey is offline
 
Join Date: Dec 2003
Location: Fairmont
Posts: 395
Send a message via AIM to Joey
And that in no way stresses the differential(s)? Not that it sounds like it would.
__________________
Mazda Savanna RX-7
stage 2 motor | spaced wheels
Reply With Quote
  #3  
Old 01-03-2004, 08:32 PM
ax0n
Guest
 
Posts: n/a
Gear differentials (like the stock white one and the red one that comes assembled with the front axle of the AWD kit) don't really get "stressed" because of driving. I am kind of new to R/C cars as far as differentials are concerned, so I don't know much about the ball differential other than what I've gained through some reading here and there, and my own personal experience. In real life, many limited slip differentials have friction plates, which are like clutches or brake pads, and eventually wear out after 100,000 miles or so. Once they wear out, they're not much worse than a gear differential as far as I know.

The only odd wear I'd expect to see is maybe stripping the differential screws, because you have to come at the front differential from an angle. Be careful working on the screws and you should be fine.
Reply With Quote
  #4  
Old 01-04-2004, 09:51 AM
Mr BigShot Mr BigShot is offline
TinyRC PRO Modder
 
Join Date: Nov 2003
Location: Wisconsin
Posts: 69
Ball difff ?

I have the ball diff in the rear if i just tightin it up real good it wont slip ?
Reply With Quote
  #5  
Old 01-04-2004, 10:21 AM
ax0n
Guest
 
Posts: n/a
tighten it real good and it will be almost as good as a solid rear axle. If it's in the rear, you can get to the screws (again, one at a time, through the spokes in the wheel without removing the body shell. Tighten them snugly, not overly tight, as you might strip the differential.

Once that's done, spin one rear wheel with your finger. The other one should spin with it exactly, versus not spinning, or spinning the other direction. Note, making the rear differential lock up more will slow you down on low speed cornering, but if you can still easily oversteer (drift) through corners if you don't have AWD.
Reply With Quote
  #6  
Old 01-04-2004, 03:54 PM
scott scott is offline
TinyRC Newbie
 
Join Date: Dec 2003
Location: clovis ca.
Posts: 16
any one use a ball dif front & back?
Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
The Ball Differential: LSD, USD, or LGD? Turnination Guy XMODS Parts and Hop-Ups 0 02-03-2005 01:29 AM


All times are GMT -5. The time now is 11:56 PM.


Powered by vBulletin® Version 3.7.3
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
Mini Inferno Sale - Up to $85 Instant Savings!
Micro-T Hop-Ups
RC18R, M18, Micro RS4, Mini-LST, TamTech-Gear, Minizilla, RC18T, RC18B, RC18MT
shop.tinyrc.com Products
Tiny RC Community News
[03/17/10] Kyosho Mini-Z F1 MF-010 SP2... : The Kyosho Mini-Z F1 MF-010 SP2 Carbon Limited ASF 2.4GHz Tx-Less Chassis Set - more»
[10/23/09] Kyosho Mini-Z MR-03 In Stock! : The Mini-Z MR-03 (http://mr-03.com) is now In Stock and Pre-Orders are shipping! - more»
[09/06/09] Labor Day Savings - $5 Off... : Labor Day traditionally marks the unofficial end of summer - but we're not ready to let go! So, we - more»
Mini-Z, Mini-Z Racer, MR-02, MA-010
M18, M18T, RC18T, Mini-LST, Mini-T, Micro RS4, XRay, 1/18, 18th scale
XMODS, XMOD, Micro Flight, ZipZaps, ZipZaps SE, Bit Char-G, MicroSizers, TTTT, Plantraco Desktop Rover, SuperSlicks, Digi Q
Mini Inferno, Mini Inferno ST, half EIGHT, 1/16, 16th scale
Epoch, Indoor Racer, 1/43, 43rd scale
E-Savage, eSavage, eZilla, e-Zilla, HPI
Robots, Bots, Bipeds, Wheeled, Manoi, Roomba, NXT, Lego, Hacking
Crawling, Crawlers, Micro, RC, Losi Mini-Rock Crawler, Duratrax Cliff Climber
Kyosho Minium, Caliber 120, Minium Forums
Mini-Z Hop-Ups, Mini-Z Parts, Mini Inferno Hop-Ups, Mini Inferno Parts, M18 Hop-Ups, M18 Parts